/* */ Beulah Bee: DIY Distress Ink Storage

September 22, 2014

DIY Distress Ink Storage

About five years ago, I made a storage container for my distress inks with 20 available slots and was certain it would be large enough to accommodate any future purchases. Hah!

So I recently crafted a new container that is larger than the original with some minor modifications. I decided to document the process and pass it along via this post in case others might want to make one.

All my photos can be enlarged via the lightbox feature--just click on them for a close-up view.

You will need:

- One sheet of foam core board (20" x 28" - 3/16" thick)
- Utility knife and an extra blade or two
- White glue (I used Elmer's)
- Ruler and pencil

Measure and mark your pieces using a ruler and pencil:

I've provided measurements for a box that will hold 28 ink pads but you can modify the design (make it taller, add more columns, etc.) to create a container that fits your needs. Mine will sit upright on a shelf next to my craft table so I sized it accordingly.

Back = 6 - 9/16" x 13 - 7/16"
Top & Bottom = 3" x 6 - 9/16"
Left/Right Sides & Center = 3" x 13"
60 Strips = 1/4" x 3"

Cut out the pieces using a utility knife (don't forget to protect your table surface).

Cutting tips:  Make multiple SLOW passes with the knife (don't try to cut through the entire thickness at once). Keep your knife straight up and down (parallel to the edge) and the blades sharp. Don't worry if some of the center foam flakes out because you can turn the rough edges towards the inside when you assemble it.

Cutting the strips is pretty easy--just make longer lengths first and then shorten them into smaller pieces.

Mark guidelines on the left/right sides and center pieces:

It will be easier to attach the strips if you mark lines for them first. I left a 1/4" gap on each end, then made marks for a 1/4" strip followed by a line for the space in between which was 5/8". Make sure the measurements match on all the strips. Remember you will have to mark both sides of the center strip.

edge + 1/4" + 1/4" + 5/8" + 1/4" + 5/8" + 1/4" + 5/8" + 1/4 + 5/8"  etc.

Glue the strips to the side and center pieces:

Apply glue to the paper side of the strips and attach to just one side of left and right side pieces. Glue strips to both sides of one piece and this will be the center support.

As with all things glue--don't use more than you need. A light, thin covering is sufficient and will set more quickly.

Assemble the box:

Build your box by attaching the top and sides to the back in sections. Make sure the edges line up evenly and hold in place until the glue begins to set.

Install the center post:

Make a mark at the center of the top and bottom pieces to assist with guiding the center post into position. Apply glue to the back, top and bottom of the center post and slide it in place.

Insert your ink pads and you are done!

I printed a Ranger ink template on plain paper, cut out the strips of text and glued them to the front of the pads (I didn't have printer labels). Then I tinted the labels with ink.

I did attach a small wooden base to mine because of the uneven wire shelf it will sit on but that is optional and won't affect how the container itself functions.

If you like to build things and need better storage for your ink pads, you might want to consider this. The end result is a lightweight but sturdy, custom container that costs very little to make and can be modified easily to fit your needs.

If you have any questions or need some advice leave a comment or send an email and do share this post with others who may be interested.

Update: I modified this storage tower when I cleaned-up my craft room. If you'd like to see the new version, here's the link.